Current Position:Home > Netra t1 105 keeps going into init 0 everynight without reason

Netra t1 105 keeps going into init 0 everynight without reason

Update:11-30Source: network consolidation
Advertisement
I have Solaris 9 installed on a netra t1 105 which goes into half every night. I have turned off the power management and the logs in /var/adm/messages does not show anything unusual.
<div class="pre"><pre>Oct 19 14:16:25 dev-sol9 pseudo: &#91;ID 129642 kern.info&#93; pseudo-device: vol0
Oct 19 14:16:25 dev-sol9 genunix: &#91;ID 936769 kern.info&#93; vol0 is /pseudo/[email protected]
Oct 19 14:17:22 dev-sol9 sendmail&#91;184&#93;: &#91;ID 702911 mail.alert&#93; unable to qualify my own domain name (dev-sol9) -- using short name
Oct 19 14:17:22 dev-sol9 sendmail&#91;183&#93;: &#91;ID 702911 mail.alert&#93; unable to qualify my own domain name (dev-sol9) -- using short name
Oct 20 09:21:30 dev-sol9 genunix: &#91;ID 540533 kern.notice&#93; ^MSunOS Release 5.9 Version Generic_118558-14 64-bit
Oct 20 09:21:30 dev-sol9 genunix: &#91;ID 943905 kern.notice&#93; Copyright 1983-2003 Sun Microsystems, Inc. All rights reserved.</pre></div>
<div class="pre"><pre>bash-2.05# eeprom
tpe-link-test?=true
scsi-initiator-id=7
keyboard-click?=false
keymap: data not available.
watchdog-timeout=65535
watchdog-enable?=false
ttyb-rts-dtr-off=false
ttyb-ignore-cd=true
ttya-rts-dtr-off=false
ttya-ignore-cd=true
ttyb-mode=9600,8,n,1,-
ttya-mode=9600,8,n,1,-
cpci-probe-list=0,1,2,3,4,5,6,7,8,9,a,b,c,d,e,f
pcia-probe-list=1
pcib-probe-list=1,2,3
mfg-mode=off
diag-level=max
d7s-flipped?=false
#power-cycles=332
system-board-serial#: data not available.
system-board-date: data not available.
last-poweroff-cause=0
env-monitor=enabled
shutdown-temperature=72
warning-temperature=67
fcode-debug?=false
output-device=ttya
input-device=ttya
load-base=16384
auto-boot-retry?=false
use-boot-table?=false
boot-command=boot
auto-boot?=true
watchdog-reboot?=false
diag-file: data not available.
diag-device=net
boot-file: data not available.
boot-device=disk:b disk:a disk net
local-mac-address?=false
net-timeout=0
ansi-terminal?=true
screen-#columns=80
screen-#rows=34
silent-mode?=false
use-nvramrc?=true
nvramrc=devalias ide-cdrom /[email protected],0/[email protected]/[email protected]/[email protected]/[email protected]:f
security-mode=none
security-password: data not available.
security-#badlogins=1074790400
oem-logo: data not available.
oem-logo?=false
oem-banner: data not available.
oem-banner?=false
hardware-revision: data not available.
last-hardware-update: data not available.
diag-switch?=false</pre></div>

The Best Answer

Advertisement
On second read Bill i see that as well.
This is going to be unrelated but your boot-device looks a bit strange as well. You are referencing different slices on the same disk, and then referencing the disk itself and then net.
boot-device=disk:b disk:a disk net
You would be ok with referencing disk and then net if the server is not mirrored. If the system is mirrored then you would want to reference that disk as well.
either :boot-device=disk net
or: boot-device=disk disk<number> net
But the next time it does it, you could try trying sync and trying to create a crash file. Once you have the crash files you can get these analysed.
As well as this pass the server through diagnostics 3 or 4 times and check the console outputs fro details.
  • Netra t1 105 keeps going into init 0 everynight without reason Update:11-30

    I have Solaris 9 installed on a netra t1 105 which goes into half every night. I have turned off the power management and the logs in /var/adm/messages does not show anything unusual. <div class="pre"><pre>Oct 19 14:16:25 dev-sol9 ps

  • Solaris 8 in Netra t1 105 Update:10-11

    Hi, all. I get a couple of netra t1 105, and I'thinking about install Solaris 8 02/02. Does the netra support that release?. If so, need I patch them?. Where can I get information about hardware platforms witch support Solaris 8. I didn�t find any ab

  • Netra t1 105: Solaris 8 & 9 install failures Update:11-30

    Hi Everyone, I have two (2) Sun Netra T1 105 machines, each with a single 360MHz Ultra SPARC IIi and 256MB RAM. Both have 18.2GB drives that have been wiped clean. I am connecting using Winblows 2000 and Hyperterminal, serial port B, 9600,8,n,1. I wa

  • D130 multihosted with 2 Netra t1 105 Update:11-30

    Hi Guru's, I want to setup an Sun Cluster for testing purposes and have the following hardware to use : - 2xNetra t1 105 1GB/2x18GB/1Gigabit Adapter (for Interconnect) - Netra st d130 Storage (3x18GB). (just one) When I try to setup the d130 I get an

  • D130 multi hosted on Netra t1 105 Update:11-30

    Hi Guru's, I want to setup an Sun Cluster for testing purposes and have the following hardware to use : - 2xNetra t1 105 1GB/2x18GB/1Gigabit Adapter (for Interconnect) - Netra st d130 Storage (3x18GB). (just one) When I try to setup the d130 I get an

  • Clean install on Netra T1 105 using terminal service Update:11-30

    Im using a windows hyper terminal session onto a Netra T1 105 and am able to boot and login as normal, however my problem lies with being able to do a fresh install from this terminal, on a normal sun box I shutdown and get the ok prompt and from the

  • Setting up a netra t1 105 Update:11-30

    all, i've got a netra t1 105 and am having trouble setting it up. i understand from the documentation that i can connect another sun box to it using the serial port. so i am doing just that with an ultra5 i have. i am using a null modem cable with db

  • Netra T1 105, issue with LOM prompt Update:11-30

    Hello all, I am having issue in accessing OK prompt from LOM menu. When I do the poweron, it sits on LOM event: power on. When I do, console it shows stand by. Please help me out here as I am working on making this server to respond. Thanks.Hi. Could

  • Netra T1 105 USB port Update:11-30

    I have a few old Netra T1 105s running Solaris 10 for hacking around with, and I'm thinking of playing with running a small RDF database (partitioned to around 10^8 triples each) off of a flash drive to reduce seek times. Currently each node has one

  • Netra t1 105 install solaris9 from terminal session Update:11-30

    I have quite a problem, I am using a windows box hyper terminal into a netra t1 105 box and am able to boot up and log into the system, however as i am on a windows box i dont have the stop-a button to press when i power it down so as to boot from cd