Current Position:Home > LPT port control via a servlet

LPT port control via a servlet

Update:11-30Source: network consolidation
Advertisement
I'm not to sure if I am on the right track, but so far I have a device wired into my lpt port (running winXP) and want to basically be able to send power to specific pins (I belive it is capable of 5V). I have looked online and through manuals and have found little information (most deals with reading and writing bits, or getting printer status, etc). I was wondering if anyone could point me in the right direction, I have very little experience writing software that interacts with hardware, I don't even know if windows will let java control the ports at that level or not. Any help would be appreciated. Thanks.

The Best Answer

Advertisement
You can't do it directly from java.
If you were really desperate to do it you would probably have to look at using JNI and writing some C code.
  • LPT port control via a servlet Update:11-30

    I'm not to sure if I am on the right track, but so far I have a device wired into my lpt port (running winXP) and want to basically be able to send power to specific pins (I belive it is capable of 5V). I have looked online and through manuals and ha

  • Send 102 bit data through the LPT port??I have to send 102 bit to my interface board using the LPT port, through one of the data line and be able to read data from the input line, I don't know how to realize such a task.Thanks Update:10-11

    Let me describe you the program I have to write: I have to send 102 bit serialy using one of the data line of the LPT port to a device and be able to read back data sent from a device register throug one one of the input port pin for instance pin 10

  • LPT port access Update:11-30

    I am in a project in which i try to send signal via LPT port and through which control the speed of a dc motor I want know...if it is possible to do with java..& how????? plz..reply. : )Take a look at https://msdn.microsoft.com/en-us/library/windows/

  • Windows 7 redirecting LPT ports to Terminal Services is broken compaired to Vista and XP Update:10-11

    Hello forum We have encountered an issue with mapping LPT1 ports from any terminal server be it 2003 or 2008, the problem is the same. Our XP clients and Vista clients works fine. Seems this issue is only present on Windows 7. We have a program that

  • Hot to install HP DeskJet 710C (LPT Port) on Solaris 10? Update:11-30

    Hi. I'm trying to install HP DeskJet 710C printer on LPT port. There is no such model in the list of Printer Administrator. I tryed few models on /dev/lp1 and /dev/ecpp0 but with all I get message "out of service". Printer is fully functional. I

  • Extended ACL TCP port control Update:11-30

    Hi all, I have configured an acl to control traffic going in/out of an interface via tcp ports. However, after applying the acl to the interface, i find that eventhough ports are allowed, traffic is blocked by the acl. I suspected that it could be th

  • Dot1x port-control auto protocol down (ACS5.3) Update:11-30

    Hello everyone!  I urgently need your help please.  I would like to configure the ports of a switch for 802.1x.  when I type the command: Dot1x harbor auto-control on the interface, the protocol is down and users are disconnected wiring.  Can someone

  • LPT Port read Update:11-30

    Hi, I am using  the "in port.vi" in labview to check if a printer is hooked to any of  my lpt ports before I send a print command to them. it is working but it freezes every now and then. my lpt port addresses are 0378 (local on mother board), A

  • Accessing printer port control lines Update:11-30

    Is it there a way to set and read the printer port control lines with Labview? The oparating system will be Windows2000 or XP. I would like to select the channel and readout an ADC with MUX (LTC2408). Peter Nyffeler mailto:[email protected] Tel P 01

  • Tecra S3: LPT port - EPP mode not available Update:11-30

    How Can I change LPT port mode to EPP in Toshiba TECRA S3 ? In the BIOS settings only ECP and SPP are available, but I have memory programmer that needs to be connected to LPT port working as EPP. It doesn't work in ECP or SPP.Maybe it's not so simpl