Current Position:Home > How to make PWM signals In Labview 7.1

How to make PWM signals In Labview 7.1

Update:10-11Source: network consolidation
Advertisement
How to make PWM signals In Labview 7.1, Could someone give me .vi for examples. Thank you.

The Best Answer

Advertisement
There is a shipping example that shows PWM if you have installed
NI-DAQmx.  You can open the example through Help >> Find
Examples >> Hardware Input and Output >> DAQmx >>
Control >> General PWM-Counter Output VI.
Good luck!
Micaela N
National Instruments
  • How to make PWM signals In Labview 7.1 Update:10-11

    How to make PWM signals In Labview 7.1, Could someone give me .vi for examples. Thank you.There is a shipping example that shows PWM if you have installed NI-DAQmx.  You can open the example through Help >> Find Examples >> Hardware Input and

  • Problem when combinning PWM signal and Analog signal TOGETHER! Update:10-11

    Hello everybody, first of all i have DAQmx 6212, and i need to run a small water pump (9V-16V) which needs to be driven by a PWM signal; also i have a motor (5V-13V) for a water valve that needs to be driven by a analog signal and it has a built in a

  • Measuring PWM Signal with NI9423 with C-RIO 9073 Update:11-30

    Attachments: Simulator1.vi ‏114 KBEh..sorry. I do not know what happened, but it seems like my questions is gone in my previous post. Let me recap, I'm new to NI Components and LabView. I wanted to measure 8 PWM Signal generated from a controller (20

  • Generating PWM signal using Signal Express Update:11-30

    Hi,    Would anyone help in generating PWM signal usinf Signal Express 2.5.1.   I am using a cDAQmx and connected NI 9472 to the slot number 6 to output the PWM signal. Also I have connected a NI 9421 to the slot number 5 to acquire the PWM signal, s

  • Generate PWM signal with 6602 utilizing load cell feedback Update:11-30

    Hi Everyone, I am new to LabVIEW so I apologize if this question is elementary but I really need some help with the coding. First of all, I need to generate 8 independent PWM signals to control 8 separate linear acuators using the NI 6602 board. I ha

  • Using excel to generate signal in labview Update:10-11

    Hi there I am having a trouble in generating a signal in labview using excel and then plotting it as waveform. In excel file, I have 2199 rows and 9 columns with time in second and I want to plot time against other columns except column 1. In rows, I

  • I am trying to log data from 4 voltage input signal using labview, but when i use DAQ assistant i am able to log data from one signal at a time only. Update:10-11

    I am trying to log data from 4 voltage input signal using labview, but when i use DAQ assiatant i am able to log data from one signal at a time only.I am trying to get all 4 input data to logged in a single file againt time. I am new to Labview, I ne

  • Want to input interference signal in labview + perform bandpass filtering/demodulation Update:10-11

    Hello to whom it may concern, I have a fiber-based OCT system linked to a Tektronix TDS 2024B digital oscilloscope, with which is showing the interference fringes of the low-coherence lightsource. The signal is linked to the computer using the NI DAQ

  • Problem with PWM signal, Please Help! Update:11-30

    Hi all, I am designing a PWM signal where its output is going to connect 4 optocouplers to drive a H-bridge MOSFETs. However, I am now having a problem of getting an output signal strong enough to drive the optocoupler.  I have attached the Multi-Sim

  • How to simulate pwm wave using labview Update:11-30

    has anyone have a built vi for pulse width modulation(PWM),or give me pointer in building its simulationHi, If you just want to generate a PWM signal you can use a square waveform VI as shown in attachment. You can insert it directly in your code or