Current Position:Home > Avoiding BPM ?

Avoiding BPM ?

Update:10-11Source: network consolidation
Advertisement
Hi folks,
Currently i have developed a scenario
File->XI->Proxy(Sync)->(File and then JDBC) using BPM.
Basically the response of proxy i am writing in a File and then in a table..Just to maintain this serial order(File and then table)i have used BPM..I know i can do the samething without BPM but i need to maintain the sequence also..
I can determine multiple receivers at receiver determination step only(as same message is being sent to both party) but they should be triggered in sequential order.
Any suggestions..
Regards,

The Best Answer

Advertisement
Any clue on this...
Regards,
  • Avoiding BPM in a rfc to file scenario Update:11-30

    Hello,      I am using a RFC to access data and post a file, i donot need the response, can i avoid the BPM by anyways, i donot want to use bpm, can this be done. Regards, Anirban.Hi Anirban, These links are 2 RFC lookups done by Michal and Sravya. T

  • How to avoid BPM SYSFAILerror in queue Update:10-11

    Hi Friends, I just designed a sync/asynch bridge. sender abap proxy synch... whenever there is any failure, the message goes to sysfail status in smq2 and sxmb_moni. I am using dedeline/exception branch also ? I just want to make sure if any message

  • Avoiding BPM ? Update:10-11

    Hi folks, Currently i have developed a scenario File->XI->Proxy(Sync)->(File and then JDBC) using BPM. Basically the response of proxy i am writing in a File and then in a table..Just to maintain this serial order(File and then table)i have used

  • Error in Multi-mapping without BPM Update:10-11

    Hi frnds, I am doing a scenario File-XI-File. I am using the multi-splitting thing in the Message mapping. I have taken care of all the occurance's and "enhanced" thing in the IR and ID resp. I m using SP16. I want to avoid BPM. But therez sme e

  • File to sync bapi_multimapping_without bpm Update:10-11

    Hi All, I have done a file ->bapi -> response to file testing interface using the adapter modules. My actual scenario is : Source file has multiple lines and for each line i have to call a bapi. The response of the BAPI needs to be appended in a fil

  • Message split without BPM? Update:10-11

    Can we do correlation (message merge) without bpm. I mean Is there any adwanced service pack which support this,so that we can avoid bpm?Hi, Ur subject and ur question is confusing..... Message split means splitting the one message into N message tha

  • B2B Addon - BPM Scenario Question Update:10-11

    We have SAP  PO 7.4 single stack working on B2B Scenarios. We will be using AS2 Adapter to send and receive ANSI X12 messages like POs inbound, Order acks Outbound, PO changes inbound etc. We installed B2B Add on ESR Content and has some sample scena

  • STEPS in BPM for synchornous. Update:10-11

    Hi, I have to persist one field using BPM for synchonous. Assume it as Empid.  I am getting it from JMS and am sending to SOAP which is a synchornous interface. While sending to SOAP, i am stripping it out and sending, along with the response receive

  • BPM - Optional Multiple Send steps Update:10-11

    I have a situation where I'm doing Message Splits in BPM and subsequently Send steps. Due to MessageSplit I may  or may not produce Target messages. But Send Steps following the transformation are errored out saying no Instance found ( No message fou

  • Help in BPM: Routing data to mutiple receivers based on field content Update:11-30

    Hi All I have a scenario where my source data is from a file. Typically this file is from a DMS application and based on the contents in this file i need to send the data to 2 receivers which might be R/3 and DB or file. Though BPM may not be of use