Current Position:Home > Accessing printer port control lines

Accessing printer port control lines

Update:11-30Source: network consolidation
Advertisement
Is it there a way to set and read the printer port control lines with Labview?
The oparating system will be Windows2000 or XP.
I would like to select the channel and readout an ADC with MUX (LTC2408).
Peter Nyffeler mailto:[email protected]
Tel P 01 363 62 42, Tel G 01 632 43 60, Fax G 01 632 10 21

The Best Answer

Advertisement
Hello Werner,
Thank you for your answer in the newsgroup.
Do you know, does accesshw work with XP and all Labview versions?
Would you mind to send me your DAC's and AD's vi's? That would be great.
regards
Peter
In article <[email protected]>,
"[email protected]" wrote:
>Hello Peter,
>
>there is no need for separate Control of ADC + MUX;
>they might be tight together - shown in Datasheet.
>
>But of course you can use the Control-lines of paraport. For W2k you
>will need accesshw on you machine:
>http://zone.ni.com/devzone/explprog.nsf/webmain/49664743ded6f1da862564bc004e3a7
>f?OpenDocument
>
>I have made some vi's for DAC's and ADC's @ paraport - e.g. MAX168 or
>DAC714.
>If you need some inspiration - let
me know..........
>
>Regards & gruezi
>Werner
Peter Nyffeler mailto:[email protected]
Tel P 01 363 62 42, Tel G 01 632 43 60, Fax G 01 632 10 21
  • Accessing printer port control lines Update:11-30

    Is it there a way to set and read the printer port control lines with Labview? The oparating system will be Windows2000 or XP. I would like to select the channel and readout an ADC with MUX (LTC2408). Peter Nyffeler mailto:[email protected] Tel P 01

  • Accessing Printer Port with Windows 7 Update:11-30

    Hello all, I've been recently asked to port a Labview file from WinXP (x86) to Win7 (x64), and one of the problems I've come across is this infamous lockdown of I/O ports in Win7.  I've done lots of searching around but haven't found much that would

  • Accessing Parallel Port Control and Status Registers with VISA and Win7x64 Update:11-30

    Hello all, I've posted this in the I/O forum for VISA, but this main forum seems to get a lot more traffic so I'm posting here too. Wondering if anyone has a solution for accessing the Control and Status registers on a parallel port with VISA, now th

  • Control parallel port (data and control lines) Update:10-11

    I need to control the output on the parallel port (LPT1) - Both data and control lines.  Once the data is written (Pins2-9), I then need to toggle the Sprocket signal (PIN1) - on the parallel port. The sprocket signal is also referred to as the Data

  • How to use the Control lines of a parallel port as Input lines to be read using Labview ? Update:11-30

    The details are : NI Software : LabVIEW Version : 5.0 OS : Windows 95 NI Hardware : N/A Drivers : N/A CPU : Pentium RAM : 48 Vendor : darcom Customer Information : SPEL TESTING SPEL, INDIA [email protected] Ph: (91) 4114 53818 We do not have any DAQ

  • How do you control individual pins on a PC's printer port in Java Update:11-30

    I know in pascal but cant find out for Java. See below //// pascal controlling pins in parallel port. Basically 889 is address of the parallel //// port allowing all pins switch on for '128' or all off '0' uses CRT; { The CRT unit allows the use of "

  • How can I access the control lines of a PCI-1422 from within C++? Update:10-11

    I would like to know how the control lines of a PCI-1422 can be accessed (set) programmatically from within C++ (MS VC++7, Windows XP). A flat panel sensor connected to the PCI-1422 needs the control lines to switch on features like binning which I w

  • How can i us the parallel port of the printer to control a frequenz-generator? Update:10-11

    Hello all ! I like to  control with LabVIEW 8 student-version, the Frequenz-generator gadget . For this challenge i like to us the parallel port of the printer. I need for data flow only 2 cable. The frequenz-generator gadget need two signal : Low an

  • Controlling Printer Port (***URGENT***) Update:11-30

    I have a project that I have to control the pins of printer port (giving signal to wanted ones when the work is done closing the selected pin). So is there someone who has the code which is written in JAVA or knows the methods that I must use? Thank

  • Cannot access forwarded ports from the internet Update:11-30

    Hi all, I have a Cisco 800 Series router that i configured to do some port forwarding. However i must have done something wrong, because i am unable to access the ports . Here is the configuration file of the router. Sorry it i pasted too much info,