Current Position:Home > Access restrictions timing off by 1 hour

Access restrictions timing off by 1 hour

Update:10-11Source: network consolidation
Advertisement
I don't know if anyone else is experiencing this problem.  I have set access restrictions on my WRT610N router and they execute an hour earlier than set.
I checked the time zone settings, the system clock and all seem correct. I have a rule that is supposed to turn off access to the Internet at 11:55pm. However, the rule gets executed at 10:55pm.
This was happening on my first WRT610N which was also dropping network connections. So, I returned that unit and got a replacement.
The new unit does not drop connections but has the same timing problem.  The only solution I have found is to change the time zone to the next one that is 1 hour behind my time zone.
Please let me know if anyone else has experienced this same situation.

The Best Answer

Advertisement
My ISP is on the same town as I am. The information they are supplying appears to be correct as my WRT54G uses the same information and its rules execute properly.
I think there is a problem with the WRT610N. My solution is temporary I hope that Linksys will fix this problem. 
  • Access restrictions timing off by 1 hour Update:10-11

    I don't know if anyone else is experiencing this problem.  I have set access restrictions on my WRT610N router and they execute an hour earlier than set. I checked the time zone settings, the system clock and all seem correct. I have a rule that is s

  • WRT54GX2 Timed Access Restrictions work too well Update:11-30

    I have set three access restrictions applicable to both a laptop (ethernet and wireless MAC addresses) and a desktop.  They all work the first time; however, once they shut off internet access, they don't permit reconnection at the time they should. 

  • Problem with access restriction Update:11-30

    I have about 50 to 80 users under my internet connection and i used the router 2500 and make there repeater of the single connection but i want to restrict many of the user on interner and some on timely but is not possible with this version of produ

  • WRT54G2 and WRT54G locks-up (freezes) when blocking web sites using Access Restrictions Update:10-11

    I am convinced that a few Linksys routers such as WRT54G2 and WRT54G have a major issue when blocking web sites using Access Restrictions (Internet Access Policy). After a few hours of internet access by 15 wired users the Linksys locks-up and blocks

  • How to configure CLI/DNIS based access restriction in 5.3 ? Update:10-11

    Hi, does anybody have an idea how the setting define CLI/DNIS-based access restrictions which is defined in ACS v. 4.2 can be configured in acs 5.3 ? in v. 4 for every user in a group with 40 members  a different CLI is defined for each. How can I co

  • WRTU54G-TM Slow Setup Page and HTML Error on Access Restrictions Page Update:10-11

    I have a WRTU54G-TM Wireless Router.  It has v1.00.21 firmware and I have done a reset with no solution.  Everything seems to work, except the setup pages load very, very, very slow.  Also in Internet explorer I get an HTML error on the access restri

  • Access Restrictions bug of firmware 1.01.1 for WRT54G V5 V6 Update:10-11

    I am using WRT54G V5. The Access Restrictions function won't work properly when using firmwares 1.01.1 and 1.01.0. Ports can't be blocked by using the "Blocked Services" in this function. Now I have to switch back to 1.00.9 to make the port bloc

  • Access restriction error? not sure how to fix it.... Update:10-11

    I am trying to use JPEGImageEncoder and i imported import com.sun.image.codec.jpeg.*; fine but i get the following error on my code: CODE: JPEGImageEncoder encoder =JPEGCodec.createJPEGEncoder(outImage); ERROR: Access restriction: The type JPEGImageE

  • WRT160Nv3 problem with blocking traffic using Access Restrictions Update:10-11

    Hi. I want something quite simple. Block Youtube. I go into "Access Restrictions", choose a name for policy 1, enable it, choose the pc from the pc list, but then... if a click Deny, all other options will be disabled (greyed out, can't click no

  • Create access restriction in designer using script Update:11-30

    Hello, I am looking for a way to automate the creation of access restriction within universe. I looked in the API universe reference and it seems that there is no entries for such an object For information I use Business Objects XIR2 with SP3 Thanks