Current Position:Home > 3850 - auto qos voip cisco-phone

3850 - auto qos voip cisco-phone

Update:11-30Source: network consolidation
Advertisement
I am having an issue where it appears that the "auto qos voip cisco-phone" command is marking down my voice packets COS and DSCP values to 0.  Anyone else notice this?  I am connecting Cisco 7945 phone to the interfaces with this command applied to the interface.  I verified that the IP Phone is sending COS = 5 and DSCP = ef to the switchport.  I verified the packets inbound to the switchport and the packets outbound as they transit to the destination IP Phone's switchport.

The Best Answer

Advertisement
Hi joshua,
What is the IOS-XE version you are running on your 3850 ?
Post your switchport configuration (7945 phone connected)
Here is 3.3 QoS config guide & I noticed it says something like below qouted. So make sure this trust device command is there & your port is configured for standard VoIP port connectivity.(like voice vlan, etc)
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3850/software/release/3se/consolidated_guide/configuration_guide/b_consolidated_3850_3se_cg/b_consolidated_3850_3se_cg_chapter_01101000.html#reference_8A1C35AB2874498F90C4F5600301BE9D
"The trust device device_type interface configuration command is only supported in an auto-QoS configuration, and not as a stand-alone command on the switch. When using the trust device device_type interface configuration command in an auto-QoS configuration, if the connected peer device is not a corresponding device (defined as a device matching your trust policy), both CoS and DSCP values are set to "0" and any input policy will not take effect"
HTH
Rasika
***** Pls rate all useful responses ****
  • 3850 - auto qos voip cisco-phone Update:11-30

    I am having an issue where it appears that the "auto qos voip cisco-phone" command is marking down my voice packets COS and DSCP values to 0.  Anyone else notice this?  I am connecting Cisco 7945 phone to the interfaces with this command applied

  • Cisco 2960x - auto qos voip cisco-phone on access ports Update:11-30

    After configuring "auto qos voip cisco-phone" on a stack of 2960x switches, we later noticed that after a power cycle (config was saved first) it went missing when doing a "show run" from the interface configs, on one of the switches (

  • Auto qos voip cisco-phone Update:11-30

    Hello, I am very new to voip, second day.  I have configured a 3850 stack to trust cisco phones on the switchports with the auto qos feature. I am interested to know where else I have to apply qos for the policy's to apply. The 3850 stack is uplinked

  • Auto qos voip trust is not supprting my cisco router1800 Update:11-30

    Please some one help me.. when i am applying  Router(config)# interface FastEthernet0/0 Router(config-if)# auto qos voip trust it is giving this message  % Invalid input detected at '^' marker. thats mean i can't apply auto qos voip trust  command ..

  • Unable to issue auto qos voip on CAT2950SX-24 using IOS c2950-i6q4l2-mz.121 Update:11-30

    Hi, I am unable to issue the command auto qos voip on the interface fa0/1. I am also not able to see the command using the "?". But based on the Cisco documentation, the IOS is able to support that command. Any can help or have any ideas? Here i

  • Auto QoS Voip Trust question Update:11-30

    Hello, I am a little confused on the auto qos voip trust command. I am reading that it should be used on interior switchports like trunk ports connected to another switch. I guess my question is this: If the auto qos voip command tells the switchport

  • Question about "Auto Qos Voip Trust" on 3560X Update:11-30

    Hi, I applied command "auto qos voip trust" to the uplink interface. But I found that the interface shown command "auto qos trust" was applied when i show running-config. Could the command "auto qos voip trust" show in the co

  • Auto qos voip Update:11-30

    hi, can I configure auto qos on ISDN PRI E1 interface? Thank you. regards,paoloYes, assuming your IOS supports auto qos. Hope this helps. If so, please rate the post. BrandonRead other 2 answers

  • Cisco 6807 and 6800ia Swtich QOS for Cisco ip phones Update:11-30

    Does anyone have an example of configuring a 6800ia switch port connected to a 6807VSS parent for cisco ip phones qos.  Normally we'd use auto qos voip  but auto qos is not supported on 6800IA switches. Cant find any cisco documentation of what the I

  • Auto QoS in physical Interfaces Switch 4507R+E Update:11-30

    I'd like to take a doubt, I'm dealing with a customer that has a Core Cisco 4507R + E with 2 Sup WS-X45-SUP7-E and WS-X4748 line cards 3-RJ45-E with IOS version below:  Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-